Correction in Service Manual. CX New camera body – new parts .. The operation (except ELX) is fortunately a matter of minutes only. Digital Camera Hasselblad ELX Instruction Manual Camera body ELD Disassembly To remove the parts from the outer and inner The Adobe Acrobat Reader allows you to view and print Hasselblad Historical documents in PDF format. A free copy of the Acrobat Reader is available from.

Author: Malazragore Zulkishura
Country: El Salvador
Language: English (Spanish)
Genre: Science
Published (Last): 3 February 2011
Pages: 219
PDF File Size: 18.82 Mb
ePub File Size: 11.82 Mb
ISBN: 249-1-66189-230-9
Downloads: 1473
Price: Free* [*Free Regsitration Required]
Uploader: Kigarisar

I can be either called, or emailed, to answer any questions you may have.

If you are photographing a wedding, it is a good hasspeblad to perform this particular check each time you change film magazines. The manual came directly from Hasselblad.

Fit the circuit board in position. While you are holding it in, check to see that both of the rear flaps are opening all the way. I recommend, however, that you only use one battery at a time in your camera.

Don’t have an account? Remove the screw Page 11 Camera body ELD Disassembly Remove the two long screws located towards the front of the camera shell. Remove the pinspring retainer, spring and the upper actuating arm Have you a cable or wire release with which you could release the shutter, as a reepair exercise? Use extreme caution manuao following this procedure! This should be between 40 and 60 grams.

The other two holes are the holes that fit over two pins on the shutter blade ring. There is, however, something that you can do to lessen the chances of this happening to you At one time, I had a franchise for Hasselblad and was given the opportunity to make this copy of the accessory repair manual.

Hasselblad repair manuals by Dick Werner

Unlike the OP, I can sometimes get the shutter to release by pushing the shutter release button, but only about hasspeblad other time I press it actually pretty consistently the first press doesn’t fire the shutter, but the second consecutive one does. Turn the gear in a clockwise direction until the check repai This is why it is replaced during an overhaul. At this point, the magazine has been properly loaded.


Camera body ELD Front bayonet plate Front plate reassembly Fit the four bayonet tongues and secure with eight screws This applies to storing cameras and lenses over extended periods repaie time, so there is no need to fire the cameras or “trip” the lenses before storing them. So you try to get the lens off the body, but it won’t come off.

Here is the procedure to be followed:. See ” way not to get a photo with a Hasselblad”. When something goes wrong with your camera, such as a broken main spring or flash repairr in your lens, you’ll know immediately because all of a sudden the camera will jam or the flash won’t fire.

The original C bodies, made in andhad mahual air piston not unlike the piston on your storm door which served as a shock absorber to absorb the shock of the flaps opening and closing. Camera body ELD Adjustment Check that the magnet arm has free movement between the shanks of spring during exposure. Here’s hassleblwd you should do: The light trap is a piece of foam that prevents light from entering the magazine when the dark slide is removed.

Look into the front of the lens and fire the camera. Because the crack is very small and is hidden by the smaller piece that is riveted to the blade, you cannot see this crack by looking into your lens.

Back to Top What is the proper way to load film mabual an older style Magazine gepair, 16 or 24? Turn the take up spool, winding up the paper until a row of repaor or a two-ended thick arrow across the back of the paper appears in the middle of the take up spool, as seen from the rear of the spool holder. Insert the spool holder into the shell, and lock it into place with the locking hasslebald. Why did one of my shutter blades break?


But if you constantly shoot shots and then charge the battery for 7 hours, your battery wouldn’t give you 1, shots anymore; it would only give around shots. If you’re still in doubt after that, you can test it by changing it for another one too. Every picture taken with the magazine that has two extra notches will show those two notches on every negative, and so on.

How should I maintain my ni-cad batteries? Insert the dark slide in the magazine and try to fire the body.

Also, notice how long the one-second exposure actually is. If you are using more than one tube, remove the lens first, then remove the tube that is next to the lens, then remove the tube that is attached to the body. With the magazine 12, this should bring the number 7 into the window. Share This Page Tweet.

Hasselblad 555ELD Service Manual

Unit for infrared remote release of the Hasselblad ELD. While looking into the opening on the back of the shell, turn the film advance key clockwise until the number 1 appears in the opening on the back of the shell. The battery in my electric body died in mid-cycle. It does not contain info haseleblad the dedicated flash sensor, which is covered in my body repair manual.